On: Flashes (On: 0.125 Article updated 20/05/2019. Techniques to Ensure Your Thermal Receipt Printer is Functioning Properly. E-Class Mark III- seems to be printing very light. 7. Last Modified Date. Light/Faded Print with Double-sided Printing 000043969. If your Star TSP100 thermal printer is not cutting in between the first receipt (Merchant copy) and second receipt (Customer copy), then follow the steps below. It printed too lightly at the 3-star setting and has not printer normally since. Make sure that the printer is well away from heaters and other sources of extreme heat. Make sure that the printer is not exposed to direct sunlight. Ensure the printer is in a clean, dry and cool location if possible. On: Flashes (On: 0.125 … ... What are the steps to setting up my Zebra TLP 3842 Thermal Transfer Printer? The printer will shutdown to prevent damage to the board. Jun 27, 2018 • HSM Article. No ribbon is used in direct thermal printing, which creates the image directly on the printed material. The printers motherboard is too hot. Creating long-lasting, high quality labels, thermal printers are a great choice. Bob Bruner from RACO Industries demonstrates how to properly clean the print head of your thermal label printer. NOTE: Printers being used in climates where the moisture level is high, or during hot weather, are especially susceptible to this issue. Read More>> Faded or poor print. However, if your print quality is going down or you are printing incomplete labels, your printer could be experiencing a common printer fault. This combination of lights indicates the printer has overheated. Note: if the problem occurs after printing from your application, verify your driver/software configurations Note: If there is a flood coating or preprint on the label surface where the print issue is occurring check with your supplier for corrective action. Make sure all settings match the printer settings to avoid intermittent issues. Looking for tips on how to fix your Thermal Printer? Printer is Not Properly Cutting Receipt. Normal operation automatically resumes once the printer has cooled. Information. Go to the computer Control Panel (Usually: Start >> Control Panel) Select Printers and Faxes; Right Click on the Star TSP100, and select Properties Not printing receipts. A lot of the times the printer is not actually broken but instead, the thermal paper is being loaded incorrectly or the wrong paper is being used. The five most common thermal printer faults are: 1. Article Number. PX4i - labels are printing poorly 3400 - Print quality issues Poor print quality Intermec Easycoder Print Quality Printer is printing too light or too dark. Problems and Resolutions Problem. I recently put new ink (hp brand) in my printer, and though a test page prints fine, when I try to print a pdf of music, it prints way too lightly (I cannot see the staff lines that should be printing...in other words, not everything is being printed and what is printed is printing way too … If no status lights are lit, it means the printer is … The QLn Series Printer is a native ZPL printer and may require a different setup for the darkness and print quality. I am using the seagull driver. The printers motherboard is too hot. Make sure you are using recommended Brother Genuine Thermal paper. The printer will shutdown to prevent damage to the board. Make sure that the room where you are using the printer is not too humid. Paper loaded in the incorrect orientation is a common problem. The READY and ERROR lights on the front of your printer turn on or flash in different patterns to tell you about the printer's status and potential problems that can affect printing: If the READY light is on, the printer is working normally. A build-up of dirt. My printer HP Officejet J6450 All in One started printing very lightly after I tried to pring a document with 3-star setting quality. 6/27/2018 9:27 PM. Question/Problem. Datamax E-Class Mark III - ink faded E-Class Mark III- printing light on the … A lot of the times the printer is not actually broken but instead, the thermal paper is being loaded incorrectly or the wrong paper is being used. 4. Troubleshoot the iPad instead. PM4i not saving sensitivity settings. System. It can also make the print smear or blur. Global POS tech manufacturer and a leader in retail, hospitality, cannabis, and more. Troubleshooting printing Printed receipts have a tiny font or are too small to read If receipts printed from your Star TSP receipt printer appear in a tiny font and are difficult to read, this is likely due to a paper size configuration issue. You can make prints lighter or darker by adjusting the print density setting in the printer driver’s dialog box or the RJ Utility. Q: My receipt printer is printing blank receipts.. A: Check that you are using thermal paper.Plain paper will not work with the Star TSP100.